- Products
- Moulds for containers & deposits
- Mould for funerary construction elements
Moulds for precast concrete elements for funerary constructions. This denomination groups a set of moulds built specifically for the production of niches, pits and columbaria, which are widely used in many regions of the world as funerary construction elements for the burial of coffins and funerary ashes.
The niches are boxes of concrete with a front opening which is sealed after the introduction of a coffin. On the other hand, the pits have upper and lower opening to stack them and form an underground hollow column, where are buried several coffins in height. Finally, the columbaria are niches but on a smaller scale, since its purpose is to hold urns with funerary ashes.
In these three types of mould, there is a fixed component that casts the interior surfaces with the required conical slopes. In the case of niches and columbaria, this element may be designed for the casting of more than one burial hollow. Hinged to this fixed part are the sides of the mould, which cast the outer surfaces of the funerary construction element. Moldtech can design and build tailored the moulds for funerary construction elements, according the regulations that the mentioned precast elements must comply with.
Additionally, it is possible to implement a system of electrical or pneumatic vibration in the mould, in order to mobilize and expel the air contained in the concrete. This feature enables compacting the concrete and using a formulation of concrete less humid, what reduces the time required for harden and removal of the casted element for funerary construction.
-
FACTORY FOR THE PRODUCTION OF PRESTRESSED BEAMS AND PANELS
Portugal, Europe2016 -
MODULAR MOULD SYSTEM FOR BOX CULVERTS
Yamena, Chad, Africa2016 -
COMPLETE FACTORY FOR THE PRODUCTION OF (PRE-STRESSED) CONCRETE ELEMENTS FOR INDUSTRIAL AND COMERCIAL BUILDINGS AND BRIDGES
Honduras, South America2015 -
Complete plant for bridges
Medellín, Colombia2018 -
Precast plant equipments
Colombia2018 -
Tilting table in Spain
-
MODULAR MOULDS FOR HALF-FRAMES
Ourem, Portugal, Europe2012 -
MODULAR MOULD FOR WET-CAST BOX CULVERTS
Zielona Góra, Poland, Europe2016 -
PRISON CELLS
Uruguay, South America2016 -
EQUIPMENT FOR THE PRODUCTION OF 3D ELEMENTS
Singapore, Asia2017 -
Pouring buckets and box culvert turner
California, USA2017 -
AUTOMATIC MACHINES FOR PRODUCTION CHAIN OF PRECAST PANELS
Argentina, South America2017 -
Carrousel plant
Narela, India2018 -
FACTORY FOR PRE-STRESSED ELEMENTS
Malta, Europe2016 -
TILTING MOULDS FOR L-SHAPED WALL SEGMENTS
Benslimane, Morocco, Africa2014 -
INSTALATION 2,000 METERS OF HYDRAULIC BEAM MOULDS FOR THE PRODUCTION OF BEAMS FOR RESIDENTIAL PROJECTS
India, Asia2014 -
TURN-KEY PROJECT FOR PRECAST PLANT FOR THE CONSTRUCTION OF RESIDENTIAL HOUSING UNITS
Venezuela, South America2012 -
COMPLETE FACTORY FOR INDUSTRIAL BUILDINGS
Libya, Africa2016 -
AUTO-RESISTANT MOULD FOR PRE-STRESSED TT SLAB
Hyderabad, India, Asia2015 -
High-capacity 180º turner
California, EEUU2018 -
COMPLETE FACTORY FOR PANEL PRODUCTION
Russia, Europe2012 -
RESIDENTIAL PROJECT
Saudi Arabia, Asia2016 -
FIXED TABLES WITH PLOTTER ON RAILS
Spain, Europe2016 -
Carrousel plant
Navi Mumbai, India2018 -
COMPLETE FACTORY INSTALLATION FOR PRE-STRESSED ELEMENTS AND PANELS FOR INDUSTRIAL AND COMMERCIAL BUILDINGS
Spain, Europe2011 -
TILTING TABLE FOR CLOSURE PANELS
Norway, Europe2017 -
Self-supporting system for bridge girders
Tegucicalpa, Honduras2017 -
TILTING TABLES
Congo, Africa2015 -
ARCHITECTURAL ENCLOSING PANELS IN VERTICAL BATTERY MOULD
Portugal, Europe2016 -
Fixed table for predalle in France
FRANCE2018 -
Industrial plant for precast power substations
Algeria2018 -
MODULAR MOULD FOR WET-CAST BOX CULVERTS
Machala, Ecuador, South America2017 -
DRAINAGE ELEMENTS
Cameroon, Africa2016 -
MOULD FOR DOUBLE CHANNEL
Muscat, Oman, Asia2016 -
MOULD SIDES FOR DELTA GIRDER
Perú, South America2015 -
Moulds for bridge
Umeå, Sweden2017 -
EQUIPMENT FOR THE PRODUCTION OF BOX CULVERTS
France, Europe2015 -
MOULDS FOR NEW JERSEY BARRIER
El Salvador, South America2016 -
180º turning machines for 3D modules
Singapore2018 -
COMPLETE PLANT FOR THE PRODUCTION OF PRECAST INDUSTRIAL WAREHOUSES
Ourem, Portugal, Europe2016 -
Modular mould for wet cast box culverts
Dublin, Ireland2017 -
MOULDS FOR BASEMENT COLUMNS
Sweden, Europe2017 -
Moulds for box culverts in Lerida
LERIDA, SPAIN2018 -
SIDES AND MOULDING FRAME FOR PRE-STRESSED ‘OMEGA’ BEAM
Spain, Europe2015 -
MANUFACTURE AND INSTALLATION OF DOUBLE BOOK MOULDS AND TILTING TABLES FOR SPECIAL PANELS
Israel, Asia2013 -
EQUIPMENT FOR THE PRODUCTION OF PRECAST PANELS, FOR INDUSTRIAL AND RESIDENTIAL PROJECTS
Russia, Europe2014 -
Tilting tables
Manila, Philippines2017 -
MT20 FOR PRECAST DRY-CAST BOX CULVERTS
Santiago de Chile, Chile, South America2011 -
Manufacturing facility in Romania
Romania2018 -
FLAT PANELS AND L-SHAPED WALLS
Sweden, Europe2016 -
Fixed table in Norway
Norway2019 -
EQUIPMENT FOR PRODUCTION OF ROADWAY PRECAST ELEMENTS IN TOGO, BENIN AND GUINEA CONAKRY
Guinea Conakry, Africa2015 -
3D hydraulic moulds
Singapore2018 -
MODULAR MOULD FOR WET-CAST BOX CULVERTS
UK, Europe2017 -
EQUIPMENT FOR BOX CULVERTS
Poland, Europe2015 -
Precast power substations production plant
Casablanca, Morocco2018 -
MOULD FOR STADIUM BLEACHER ELEMENTS
Spain, Europe2016 -
MOULD FOR TT SLABS
Canada, North America2017 -
BATTERY MOULDS FOR THE PRODUCTION OF LIGHTWEIGHT PANELS
Portugal, Europe2016 -
Automatic moulds for columns
Nelas, Portugal2017 -
MOULDS FOR NEW JERSEY BARRIERS
Costa Rica, South America2015 -
COMPLETE FACTORY FOR THE PRODUCTION OF PRE-STRESSING ELEMENTS AND CLOSING PANELS
Luanda, Angola, Africa2008 -
MT20 dry cast box culvert equipment
Delhi, India2018 -
FIXED TABLES
Algeria, Africa2015 -
Production lines for girders in Slovakia
Slovakia2018 -
EQUIPMENT FOR BOX CULVERTS
Benin-Togo, Africa2015